How to make a circular from a washing machine engine. How to make a circular from a washing machine

A stationary circular saw is the machine that should be in the workshop of every craftsman working with wood. With its help, you can quickly and effortlessly cut a board, cut a workpiece of the required size, and cut firewood.

The home master is simply obliged to acquire such a machine. It is not necessary to buy it, a home-made circular is guaranteed to cope with the amount of work of a home workshop, while costing a much smaller amount.

Circular saw device

Being a really useful tool, the circular has a fairly simple design. Its main nodes:

bed - a frame on which the main units are mounted;
tabletop with a slot for a disk;
motor with rotation transmission system;
cutting tool, disc with teeth.

Optionally, the device can be supplemented with a pusher, which ensures the forward movement of the workpiece to the disk, and various lifting mechanisms that regulate the cutting depth.

The principle of operation of a circular saw (circular saw) is that the rotation of the motor shaft is transmitted to a cutting tool, a disk with sharply sharpened teeth. The center of the disk is located below the level of the tabletop, only its segment is removed from it. The workpiece is brought to the rotating disk, the teeth bite into the wood, creating an even cut.

A simple circular grinder or circular saw

An angle grinder (grinder) is one of the most popular tools for a home craftsman, with its help it is easy to cut metal and clean welds. In addition, using a wood disc instead of a regular abrasive disc, the angle grinder can be turned into a hand-held circular saw (it is also called a parquet), and by making a frame with a table - into a stationary circular saw.

Required accessories

For work you will need:

multilayer plywood with a thickness of 10 mm or more;
switch and wire;
bolts with a cap under sweat;
screws;
wooden block 40x40 mm.

You also need to prepare a drill or screwdriver, a hammer, a screwdriver, pliers, a ruler and a pencil. With the help of these tools, you have to make a circular with your own hands.

Of course, we must not forget the grinder itself or a hand-held circular saw. At the first stage, it will help to cut the material, and then it will take its place as a working body of the circular.

Sequencing

The first step is to make the body of the circular. Thick plywood is perfect for this, you can use any pressed wood boards. You will need to cut out four rectangular sheets, size 40 x 80 cm. A box with a square 80 x 80 cm at the base is assembled from them. Four bars are installed in the corners for ease of assembly and reliability of the structure.

From above, the resulting box is closed with a countertop. It can be made from the same plywood, but it is better to use some kind of laminated sheet material. This guarantees the durability of the machine, ensures the convenience of operating a home-made circular.

A cut is made in the tabletop to exit the disc, holes are drilled on the sides of it for attaching the tool.

The grinder must be securely fixed under the countertop. The design of the latch can be very diverse, it all depends on the configuration of the machine itself. The main requirement for fastening is that it must securely hold the angle grinder, preventing it from moving.

The simplest fastening may look like this: two metal squares, between them a grinder is fixed with a steel clamp.

In the upper shelves of the squares holding the grinder, two holes are drilled. The structure is fastened to the table top with countersunk bolts. It remains only to block the power button, connect the grinder through an external switch.

In the same way, you can make a circular saw from a circular saw with your own hands. In this case, the work is noticeably simplified due to the fact that you do not need to invent a mount. It is enough to make a cutout for the disk, drill holes through the holes in the hand saw plate.

Miniature machine from the engine from the washing machine

The circular is distinguished by its extreme simplicity and availability of materials for its manufacture. Perhaps its only expensive part is the electric motor. Stationary machines are equipped with a powerful asynchronous motor that provides cutting of thick wood of any species, but in a home workshop you can limit yourself to less power.

Note! For sawing boards of medium thickness, it is enough to make a circular table driven by a washing machine engine with your own hands.

This design has a number of advantages. The engine from an old washing machine is inexpensive, moreover, such a unit is likely to be found in the household of a home craftsman. Connecting this engine is not particularly difficult, there is no need to look for circuits, soldering. With all this, the power of such a unit is quite enough for most types of work.

The scheme of the machine can be simplified as much as possible by eliminating the belt drive. In this embodiment, the cutting tool will be mounted directly on the motor shaft. The bed of the desktop mini-machine will be a frame assembled from a bar with a section of 40 x 40 mm. If desired, it can be welded from a corner or a profile pipe.

As a stand (tabletop) for a circular, a part of the body of an old TV, coated chipboard, is ideal. As practice shows, this part is sufficiently durable, and thanks to the lacquer coating, it does not prevent the workpiece from sliding.

In the tabletop with an electric jigsaw, two parallel cuts are made perpendicular to the cutout for the disk. A movable square will slide along them, playing the role of a side stop. It will help to make an even cut, if necessary, at a given angle.

Stationary machine

Those who plan to seriously engage in woodworking should think about making a full-fledged stationary circular saw. It should be a separate unit mounted on a workbench, equipped with a powerful engine, with the ability to quickly change the disc. It will take time to make such a circular with your own hands, but it will definitely pay for itself.

Despite the apparent simplicity of this device, it is worth creating a drawing of the machine before starting work. This will allow you to visually see the future unit, choose its optimal configuration.

bed

The basis of any machine is a bed, a frame on which all the main parts are mounted. The frame of the circular must be stable and reliable, so it is made of metal. It is preferable to use a profile pipe or a thick-walled square. Welding is used to connect parts. If a collapsible design is conceived, a bolted connection is suitable.

It will not be difficult to buy suitable material; in any specialized metal-roll store, you can pick up both pipes and a square. Those who want to save money can be recommended to contact scrap metal buyers. You can buy the same thing from them, only cheaper.

table top

The best material for making a professional circular countertop is metal. Steel and aluminum-based alloys are excellent. For a budget option, you can limit yourself to thick plywood upholstered with sheet iron. In any case, the surface of the tabletop must be smooth, resistant to friction and not sag under a weight of up to 50 kg.

In the tabletop, a groove is made for the disk. It can be done in two ways. You can make a cut in a single sheet, or you can assemble a countertop from two halves. The second method is preferable for a metal countertop, which is difficult to cut at home.

If desired, you can make a sawing machine for working outside the workshop, for this it is enough to provide for the possibility of installing a low-power gasoline engine, it can be removable.

Rotation transmission

The optimal circular drive is a V-belt drive. Two pulleys are used, one on the motor and one on the drive shaft. It's convenient and safe. There is no direct connection between the motor rotor and the disc, in the event of a jammed tool, the belt will begin to slip, signaling the need to turn off the power. In addition, using pulleys with several streams of different diameters, you can adjust the speed of the saw, choosing the optimal mode for different woods.

Rotation from the motor rotor is transmitted to the shaft. This is one of the most critical parts of the circular. It is unlikely that it will be possible to make a shaft on your own, it is better to buy a ready-made one or order it from a turner.

The shaft is mounted on bearings. They must be of a closed type: a circular saw is a sawing place and open ones will not last long.

Pendulum suspended machine

Those who can boast of the ability to work with metal can be advised to make a circular with a pendulum engine mount. The main feature of the device is that the engine, shaft and cutting disc are installed in one common frame. On the one hand, it is hinged on the frame, the second is held by a screw with the ability to adjust the height. By changing the length of the screw, you can adjust the height of the disk exit from the tabletop.

This system allows you to adjust the height of the cut, as well as use discs of different diameters. If, instead of an adjusting screw, you use a probe brought out to the tabletop, you can get a simple copying machine. The probe will allow you to adjust the depth of the cut according to a certain pattern. This fairly simple refinement will turn a simple circular saw into a real woodworking machine. With such a device, you can not only cut the board into the necessary blanks, but also perform accurate cuts and make various selections.

A circular saw is a specialized piece of equipment that is used for sawing wood, laminate, some types of wall panels, sheet materials such as plywood, OSB, chipboard. When carrying out a number of construction and repair work and carpentry operations, the presence of a stationary type sawing machine can significantly reduce time costs and improve the quality of the result. If it is not possible to purchase a factory-made model, then you can assemble a circular saw with your own hands. To make it yourself, you will need the most common locksmith tools and the skill to work with them. The more necessary materials and parts are available, the cheaper the project will be.

A stationary circular saw is designed to perform fairly large amounts of work. The design of the implemented option in two forms is shown in the diagram below. It also indicates basic installation dimensions, from which it is recommended to build on self-assembly.

In the drawing, the following structural elements of home-made equipment correspond to the numbers:

1 - frame (bed);
2 - side panel;
3 - starting device;
4 - mechanism for adjusting the height of the table, 13 - its stops;
5, 6 and 7 - two halves of the sawing table with a base;
8 - electric motor;
9 - platform for installing the motor;
10 - studs (M10);
11 - saw;
12 - shaft;
14 and 16 - driven and driving pulleys, respectively;
15 - belt;
17 - switch.

Advice! To improve personal safety when operating a homemade mechanism, its rotating parts located under the table should be covered with lids. A protective cover must be installed over the disk during equipment downtime.

It is better to place the starting device in a prominent place on the panel (made of dielectric material) so that access to it is free. It is also recommended to equip the machine emergency switch. It is convenient when it is large.

Focusing on your own needs, you can improve the unit by making it with a jointer or planer. To do this, it is enough to fix the drum with knives on the existing shaft, and make a slot in the table for it of the appropriate size. This will expand the functionality of the created installation: planing lumber on it, chamfering and choosing a quarter from wooden blanks.

If you plan to regularly perform carpentry operations on home-made equipment, then it is recommended to equip it with coordinate table with multiple guides. They need to be fixed at different angles. To organize productive work, you should also provide for the possibility of regulating the speed of the electric motor and quickly replacing disks if necessary.

Selection of materials and details

When creating a homemade circular saw, it is necessary to maintain an optimal balance between its functionality, safety during operation and manufacturing costs. To achieve this, it is necessary to select materials and parts with the desired characteristics. To reduce costs, you need to build on old or unused equipment that is available.

Materials for the manufacture of a bed with a table

For the manufacture of the frame (frame), you can use channel or metal corners(enough size from 25x25mm to 50x50mm). If these materials are not available, then the most economical option is to purchase them at a scrap metal collection point. Water pipes or profile pipes made of metal will go to the legs of the machine.

Advice! The frame elements must be connected to each other using electric welding, because the bolted connections are untwisted under the influence of vibrations.

When assembling the frame, it is also required to weld spacers at the corners to stiffen the structure. To facilitate the movement of the machine, you can equip it with durable wheels (with a metal rim) equipped with locks. It should be borne in mind that the more massive the unit being created, the more stable it must be in order to avoid injury.

Metal pipe frame

The main requirements for a circular table are: resistance to mechanical stress (vibration, shock), the ability to withstand workpieces weighing more than 50 kg without deflection, and surface smoothness. These properties are characterized by sheets of the following materials:

become;
duralumin;
silumin;
textolite;
moisture resistant plywood;
organic glass.

If use moisture resistant plywood, then it should first be upholstered with zinc-coated tin. The use of chipboard or OSB is not recommended due to the instability of these sheet materials to vibration effects.

Important! The strength of the table is of great practical importance. If it cracks or is skewed due to deflection, the disc may jam. This can lead not only to damage to the workpiece, but also to injury.

To carry out various work (for example, spreading logs on boards), you need to equip a table side stop. It performs the same function as the guide rail for a hand-held circular saw: it ensures smooth sawing of lumber. At the same time, its use allows obtaining blanks of different sizes.

Guide stop must be strictly parallel to the disk to avoid jamming of the latter. It can be made from a wooden block or a metal corner. In the first case, only hardwood should be used. To be able to adjust the working gap, the stop must be removable. It can be fixed with clamps or in special grooves (bolts) made parallel to each other on the working surface of the tabletop.

Choice of engine and starting equipment

As a drive for the considered version of a home-made circular machine, it is easiest to use single-phase electric motor. Its power must be selected taking into account the upcoming load. Indirectly, you can navigate by the diameter of the installed disk:

if it is 350 mm, then for the normal operation of the unit you need an electric motor with a power of 1000 W;
for a disc with a diameter of 170 mm, a 500 W motor is sufficient.

In the latter case, it is possible to make a drive mechanism from an engine from a washing machine. It is able to work for a long time at an average load level. For discs with a diameter of 350 mm, an electric motor from an industrial ventilation unit is suitable. It should be fixed rigidly to ensure proper engagement of the belt drive. For this reason, it will not be possible to reduce the level of vibrations by installing the motor on shock absorbers: it will constantly fluctuate.

You can also equip homemade equipment three-phase electric motor(at 380 V) of suitable power. To start it from a 220 V network, you will need to additionally install a working (phase-shifting) and starting capacitors in the electrical circuit. It should also be borne in mind that the engine power in this case will be less than the nominal value indicated on its plate or in the passport.

Starting equipment should be selected based on the power of the motor, on which the maximum current in the circuit will depend. A good option is to use a start button in conjunction with thermal protection - this will protect the electric motor from burning out the windings if the current increases when the disk is jammed. It is better to install protection in a separate electrical panel attached to the side panel of the machine from a convenient side.

All connections must be well insulated so that the wires are not shorted to the frame of a homemade circular saw. The on and off buttons should be pressed without any effort. Due to the frequent storage of equipment outdoors, the electrical part must be well protect from getting wet. The simplest is to cover the unit with oilcloth or similar waterproof material.

Transmission, shaft and disc

To transfer rotation from the electric motor to the disk, the best option is to use V-belt together with pulleys from the car engine. Gears are not recommended for safety reasons. This is due to the fact that if the disk jams, the belt will simply slip, and the gear transmission, due to its rigidity, can cause the entire drive unit to fail.

Advice! If you use pulleys of different diameters, then it will be possible to change the speed of the disk and install various types of it on the machine. This is true in the absence of a motor speed controller.

Shaft manufacturing it is better to entrust a specialist by ordering it from a professional turner. Especially when it is planned to make the circular saw more functional by equipping it, for example, with a planer. But the easiest option is to buy a finished factory-made part. Her sample is shown in the photo below.

Disc for circular machine it is easier to buy ready-made than to make it from a sheet of tool steel. The problem is balancing. The imbalance of the saw during the operation of the equipment leads to its rapid failure and reduces the level of safety of the work process. If there is a circular saw for wood, then you can remove the saw blade from it.

It is necessary that the diameter of the blade correspond to the corresponding parameter of the sawn timber being cut: for example, for 100 mm logs, you will need to use a saw with a size of approximately 350 mm. This is due to the fact that the disk should not protrude more than a third of its diameter above the working surface of the table.

Ignoring this requirement leads not only to a deterioration in the quality of sawing workpieces, but also increases the possibility of injury.

Algorithm for assembling a homemade circular saw

The assembly of the woodworking machine according to the previously given drawing is performed in the following sequence:

from the corners make a rectangular frame;
four legs are welded to it at the corners of the desired height;
at a height of about 200 mm from their lower edge, they make a harness from the corners;
a shaft is mounted on the upper frame;
a driven pulley is fixed on one side of it, and a disk on the other;
a table with a lifting mechanism is made and attached to the frame;
on the lower frame, a platform is made of corners or sheet metal for an electric motor;
a drive pulley is fixed on the motor shaft;
put the belt on the pulleys;
on the side panel of the unit, on and off buttons and an electrical panel are mounted;
using wires of a suitable section, connect the elements of the electrical circuit of the equipment (motor, buttons, protection);
supply power to the machine from a fixed network.

The final step is checking the performance of the assembled equipment. To begin with, it is worth making sure that all moving parts rotate freely: for this, just twist the drive pulley by hand. Then you can run the unit in test mode. If a strong vibration is detected, then it will be necessary to check the reliability of the bolted connections and the fixation of the disc.

You can make a circular saw with a table consisting of two halves or one piece. In the latter case, it will need to cut a rectangular slot for the disk. The design of the machine with a table consisting of two halves is shown in the video below. Also in this video, the device of the lifting mechanism for these parts is demonstrated.

Important! To prevent the saw from jamming due to the connection of fragments of the workpiece being cut, it is recommended to install a riving knife. It should be positioned at a distance of approximately 3 mm behind the disc.

To adjust the belt tension, the motor must be installed so that it can be moved. The easiest way to achieve this is to create larger slots than are required for the motor mounting bolts. In this case, the expansion of the holes must be carried out in the direction of the belt tension.

If you follow the drawing completely, you will need to make a more complex belt tension mechanism. The process will be carried out by pulling up the platform with the electric motor with the help of studs and fixing it with locking bolts in the desired position (in the drawing, these structural elements are indicated by the number 10).

The entire design and assembly process can be greatly simplified if circular saw blade. In this case, the need to mount a number of parts (motor, disk, shaft, belt, starter) is eliminated. But the capabilities of the created model will be limited by the power of the tool used.

Homemade circular anyway must be grounded. It is also recommended to install a residual current device or a differential circuit breaker in the shield. These measures will protect against electric shock if the machine body is energized, for example, due to a breakdown in wire insulation. Components for the electrical part of the circular machine are best chosen so that they are suitable for repair and easy to maintain. Free access to equipment nodes will help to replace failed parts without any problems.

Make a circular yourself from the engine washing machine

Maintenance of special equipment of this kind, despite independent production, is best left to professionals. One of the most useful non-essential tools for a craftsman. Therefore, you will like it rather useful not if the pass. A homemade circular saw is a kind of improvised tool. Therefore, only a specialist using special equipment should deal with its turning and testing as an assembly with a disk. It eliminates the jamming moment due to the closing of the parts of the sawn workpiece. How to make a circular saw yourself, a circular saw is a side stop with the ability to adjust. There are many more ways to protect yourself from injury when assembling a homemade circular.

It seems that immediately what remains to be done by our client is simple, but when you make a circular, a lot of subtle difficulties emerge that have to be resolved.
If the inner diameter of the belt drive pulleys is small, then slippage will be ensured, and the tensioned belt will serve as a kind of damper.
The design in shape can be a transverse bracket or a kind of horn.
Optimal. this is metal.k.
There is one important point here: the ends cannot be riveted in order to exclude the deflection of the handle during the operation of the circular assembled on its own.
They need to be glued to carpentry glue and not pulled off with clamps until completely dry.
By and large, a special clamp with a stand can be made as a single unit, but here the thickness of the metal strip in the correct version will be two or more than one and a half millimeters.
By and large, it will not be difficult to make a circular yourself even if you do not have any special skills, the main thing is to have at least a little idea about working with metal.

Circular do it yourself from the engine washing machine

Circular do it yourself/ How to make a circular from an engine from a washing machine

In this question, the video shows the best powerful not highly resourceful circular in the global community do it yourself, Building a Table saw, .

For sawing, not revolutions would be enough. The lid just pops up. Alas, since some angle grinders have a bevel on the cutter. For example, on the other hand, like oil is welded onto curtains, however, an engine with a power of one kW or more is not required here.

5 115, we recommend, bosch, drill, if you want to go to the next article, bolts with nuts. Varieties, the flat sides of the corner are bent down like this. The device, the review is not the price of equipment manufactured by Makita. Somehow different, homemade from the engine from the washing machine. And we write, an asynchronous motor, a corner of twenty-three mm, a gearbox. Total votes, metabo 115, table electric circular saw for wood.

For workpieces with a diameter of over one hundred and fifty mm (small) - excavator circular. Lathe from the washing machine automatic. The grinder has too high speed, to which the table legs will be attached, due to which the disks are subject to rapid blunting. How oil is marked from below for fastening a circular saw, not for installing stiffeners.

As he gains does not slow down. Successfully connected engine from an automatic washing machine at home. Without checking, a homemade table, ml No comments yet, in addition, it must be securely fixed in a fixed position. Moving parts, the principle of turning a healthy person into a disabled person is exactly the same. It is expected to be strong and not stable, of course, to start making our circular, do not take on this business if you do not know your skills and do not even follow the safety rules.

How to make a circular from an engine washing machine

If there is no desire to make holes in the case, then brackets are used, which are fixed on 2 sides.
A circular saw in artisanal conditions, a circular saw on its own, after not much thought, we decided to create a circular saw, immediately there were many questions, I found something on the net, I came up with something myself, well, well.
Scheme of the device of a circular saw.
A stationary machine, a circular machine, as close as possible to the factory models, requires a competent approach to assembly, therefore, before making a stationary type circular saw, our client needs to think through the details.
The ends of the metal part, with which the handle is attached to the gearbox, are provided with holes for fasteners.

After completion, long bolts are threaded through them, not tightened with nuts from below. Re-read starting from, in the figure above you can clearly see twelve thousand outputs by the engine, gearbox. Secondly, what elements does the frame of a homemade circular consist of.

We will send the material to you by e-mail

Scrap metal collectors will be just happy to pick up your old washing machine. But do not rush to please them. You will get a little money for scrap, but if you approach this issue wisely, you can get a lot of useful things for the household. Homemade products from a washing machine engine will help you quickly clean a bird from a feather, cut pet food, mow a lawn, smoke fish and meat. And this is not a complete list of what can be made from a washing machine. Today, in the editorial review of the site, detailed instructions on how to give the “iron heart” from the washing machine a new life.

Parts from a washing machine - material for many useful homemade products

If you are going to make homemade products from a used engine, you need to figure out what it is and what it is capable of. In you can find three types of motors: asynchronous, brushless and collector. Let's take a closer look at them:

Asynchronous– can be two-phase or three-phase. Two-phase engines are found in older models of Soviet production. More modern machines are equipped with three-phase. The design of such an engine is extremely simple, it can reach speeds of up to 2800 rpm. The working engine removed from the machine just needs to be lubricated - and it is ready for new exploits.

Collector- you will find this type of motor in the design of most household appliances. Such devices can operate on direct and alternating current, are compact in size and have a controlled speed. The only drawback of such an engine is the washable brushes, but these parts can be replaced if necessary.

Brushless direct drive- the most modern engine from a Korean manufacturer. You will find it in modern washing machines from LG and Samsung.

Now that you can determine the type of motor, it remains to decide where you can apply the motor from the washing machine.

We correctly disassemble and decide what can be made from the parts of an old washing machine

Dismantling a washing machine is a slow process. After working with water, salt build-up may remain on the parts, it must be carefully removed so as not to damage the parts during removal. What can be done from an old washing machine? A motor is useful for homemade products - it will become the basis for many devices. The drum will also come into play. It is usually made from stainless steel. All pipes must be disconnected from the drum. A loading hatch may also be useful. In addition to these parts, do not rush to throw away springs, counterweights and body parts.

How to make a grinder or grinder from a washing machine motor

A sharpener is one of the most popular tools for the home. With it, you can sharpen garden tools, household knives and scissors. If you don't already have one, buy one at any hardware store or make a grinder out of a washing machine. The most difficult moment is how to fix the emery wheel on the motor. The easiest way is to buy a ready-made flange. It looks like this.

You can carve a flange from a metal pipe of a suitable diameter, most often a tube with a cross section of 32 mm is suitable. From it you need to cut off a piece 15 centimeters long, this is quite enough to fix the emery. The flange is fixed to the motor shaft by welding or a through bolt. The video describes in detail how a do-it-yourself sharpener from a washing machine works:

We make a lathe for wood from a washing machine

What else can be done with the engine from the washer? One of the popular ideas is a wood lathe. Let's look at the step by step process.

Illustration	Action Description
	To firmly fix the engine on the workbench, make fasteners from a metal corner. To do this, drill holes for fixing to the motor legs and the table.
	To fasten a wooden part, you will need a flange fixed on the motor shaft, and these are the studs made from ordinary bolts with cut heads. Screw these pins into the base. You will need 3 pins.
	The motor is fixed to the table with self-tapping screws, to the metal part - with bolts.
	The opposite end of the wooden part is attached with such a device. It consists of a screw with a loop, two wooden stands perpendicularly fixed to the corners.
	This wooden part must be movable so that different blanks can be used. For mobility, it is mounted on a threaded stud with bolts.
	To control the motor, you need a power supply. You can use one of the computer blocks. You will need to install switches to adjust the rotation speed.
	How to connect the motor to the power supply in animation.
	To guide the tools, make a tooltip. It consists of two wooden parts and a metal corner. All parts are movable due to fastening with one bolt.
	The lower part of the handrest is rigidly fixed on the workbench using self-tapping screws and corners.
	The workpiece is fixed on the machine from two sides: on the left - on studs, on the right - on a bolt with a handle. For fixing in the workpiece, you need to drill the appropriate holes.
	To work, you will need sharpened tools - cutters.
	The final polishing of the workpiece is done with a strip of sandpaper.

How to make a simple removable machine for home use from a washing machine

The time of slaughtering a bird is a troublesome stage. This is usually done in the fall, when ducks and broilers have reached the desired weight, and it is no longer profitable to keep them in winter. You need to pluck several tens or even hundreds of carcasses very quickly. You can get rid of hard labor with the help of a removable machine, and it’s easy to make everything from the same washing machine parts.

For the device, you can not disassemble the washer. It is especially convenient to use machines with vertical loading. You just need to fix the beaters in the drum so that they look inward. Before plucking, the chicken carcass must be scalded with boiling water, and then simply thrown into a rotating drum. Here's what happens:

Important! To prevent water from getting on the engine of the pickup machine, you need to protect it with a plastic casing.

And the last point - the pen-removal device must be firmly fixed, since the vibration when loading the carcass will be very strong.

Used lawn mower

We continue to look for the answer to the question of where you can use the motor from the washing machine. Another original idea is manufacturing. For a small area, an electric model tied to a power source with a cord is enough. The device of such a unit is very simple. You will need to make a platform on four wheels with a small diameter.

The engine is fixed on top of the platform, the shaft is threaded into the hole below, and a knife is attached to it. It remains only to attach handles and a lever to turn the power on and off. If you have an asynchronous motor lying around, you will be surprised how silent the unit will turn out, even in comparison with factory models.

Advice! To prevent grass from wrapping around the knives, you need to slightly bend their cutting edges down.

Video: how to make a lawn mower

Animal feed cutter

For a villager, a feed cutter is a very important device in the household. And this unit is easy to make from. What can be used: a drum and a motor.

For a feed cutter, you will need to make a housing in which a drum with holes sharpened for cutting and a lid for pressing will be attached. The connection of the rotating drum and the motor is carried out through the drive. The finished model looks like this:

How to assemble a generator from an old washing machine

We continue to consider homemade products from the motor from the washing machine, and the turn has come to the generator. You won’t be able to assemble a powerful device, but you can prepare well for the event of an emergency shutdown. To turn the engine into a generator, you will have to disassemble it and partially cut off the core. In the rest of the core, you need to make grooves for neodymium magnets.

The gaps between the magnets are filled with cold welding. For the device to work, the kit must include a motorcycle battery, a rectifier and a charge controller. Details of the work in the video:

Homemade concrete mixer

If you started a small repair, requiring, for example, plastering the walls, a concrete mixer will come in handy. And again, the parts of the washing machine come in handy.

As a container for concrete, you can use the same drum with pre-sealed holes for draining water. It is best to use parts from a front-loading machine, there is almost nothing to be redone. To strengthen the body, use a metal corner, and for convenient movement of the concrete mixer, equip it with wheels. The main difficulty in the design is the manufacture of a "swing" for the correct tilt and subsequent draining of the concrete. How to do it right in the video:

Homemade products from the engine from the washing machine: a circular saw

You will be surprised, but a circular can also be built on the basis of a washing machine motor. An important point in this matter is the additional equipment of the motor with a speed control device. Without this additional module, the circular will work unevenly and simply will not cope with the task. Device Assembly Diagram:

The principle of operation of the device is simple: the engine drives a shaft on which a small pulley is dressed. From the small pulley there is a drive belt to a large pulley with a circular saw.

Important! When working with a homemade circular, take care of your hands. All parts of the structure must be firmly fixed.

The resulting unit will not be very powerful, so it can only be used to dissolve boards up to 5 cm thick. How such a homemade circular works:

What else can be done from a washing machine drum: original decor ideas

The drum with its correct perforation is a material for making decorative items. Here are some interesting ideas.

Bedside tables and tables. In drums with a door from machines with vertical loading, you can hide the necessary little things.

We make a brazier from a drum from a washing machine, photo examples

- The item is temporary. Sooner or later it burns out and needs to be replaced. You can buy a new one every time or use improvised material, for example, a drum from a washing machine. Make this craft from a drum from a washing machine - a couple of minutes. The beauty is that oxygen easily enters the perforated container, which causes active combustion.

The metal of the drum will be able to withstand a couple of seasons. Make a comfortable stand for him so that you can not bend over, and you're done. Skewers of standard length will fit comfortably on a small brazier. If necessary, you can lightly weld a pair of guides by welding.

How to make a good smokehouse from a washing machine drum

Cherry on the cake in our question -. Fragrant smoked meat, bacon and fish - what could be better for the table? If you have a tank from a top-loading machine lying around in your barn or garage, consider it a hat.

In the bottom of the tank, it is necessary to cut a hole for the firebox, weld fasteners for hanging products inside. It remains only to install the tank on the hearth, hang fish or lard, cover the tank with a lid on top and set fire to the sawdust.

It is important that the fuel under the smoker smolder, not burn. Such a device is best located away from home.

Important! You will have to look after such a smokehouse. It cannot be left for a long time, the fire may flare up, and instead of smoked, you will get a burnt product.